Interstate 70 in Maryland

From the AARoads Wiki: Read about the road before you go
(Redirected from Maryland State Highway 570)
Jump to navigation Jump to search
This article is about the section of Interstate 70 in Maryland. For the entire route, see Interstate 70.

Interstate 70

I-70 highlighted in red
Route information
Maintained by MDSHA
Length91.85 mi[1][2] (147.82 km)
Existed1962–present
Tourist
routes		 Historic National Road
Chesapeake and Ohio Canal Scenic Byway
NHSEntire route
Major junctions
West end I-70 / US 522 at Pennsylvania border near Hancock
Major intersections
East end I-695 / MD 570 in Woodlawn
Location
CountryUnited States
StateMaryland
CountiesWashington, Frederick, Carroll, Howard, Baltimore
Highway system
← MD 68→ MD 70
← MD 568MD 570→ MD 575

Interstate 70 (I-70) is a part of the Interstate Highway System that runs from Cove Fort, Utah, to Woodlawn, Maryland west the city of Baltimore. In Maryland, the Interstate Highway runs 91.85 miles (147.82 km) from the Pennsylvania state line in Hancock east to the Interstate's eastern terminus at its junction with I-695 in Woodlawn, where the freeway continues east as Maryland Route 570 (MD 570) to its end at a park and ride lot on the western edge of Baltimore. I-70 is the primary east–west Interstate in Maryland; the Interstate Highway connects Baltimore—and Washington, D.C., via I-270—with Western Maryland. The Interstate serves Frederick and Hagerstown directly and provides access to Cumberland via its junction with I-68 at Hancock. I-70 runs concurrently with its predecessor highway, U.S. Route 40 (US 40), from Hancock to Indian Springs in Washington County and from Frederick to West Friendship in Howard County.

I-70's route from Frederick to West Friendship was constructed as a divided highway relocation of US 40 in the early to mid-1950s and a freeway bypass of Frederick in the late 1950s. The first section of the Interstate to be marked as I-70 was an upgrade of US 40 near Hancock in the early 1960s. The remainder of the Interstate highway in Maryland west of Frederick was built on a new alignment in the mid- to late 1960s. I-70 was constructed from West Friendship to its present terminus in Baltimore in the late 1960s. The highway from Bartonsville in Frederick County to West Friendship was upgraded to Interstate standards in the mid-1970s. The final non-limited access portion of I-70 between Frederick and Bartonsville was eliminated in the mid-1980s. The Interstate has been upgraded through Frederick in a series of projects that began in the late 1990s.

I-70 was intended to enter Baltimore as an east–west freeway that had been proposed since the 1940s. Around 1960, I-70 was planned passing through a pair of parks and several neighborhoods in West Baltimore to end at an interchange with I-95 and I-83 at the Inner Harbor in Downtown Baltimore. A subsequent proposal based on a review of the 1960 plan moved I-70 to a new alignment that triggered community opposition, which resulted in a new design process in the late 1960s. A new plan was introduced around 1970 that would have moved I-70's eastern terminus to Southwest Baltimore (Sowebo). However, community opposition to the Interstate's planned route through the city parks resulted in I-70 being removed from city plans in the early 1980s.

Route description

I-70 has several official designations along its course through Maryland. The Interstate Highway is designated Eisenhower Memorial Highway from the Pennsylvania state line east to I-270 in Frederick. The highway received this designation from a 1973 act of Congress commemorating the route of the 1919 US Army convoy from Washington, D.C., to San Francisco, California, in which President Dwight D. Eisenhower participated, an ordeal that served as one of his inspirations for the Interstate Highway System.[3] All of I-70 in Frederick County was designated the Korean War Veterans Memorial Highway by the Maryland General Assembly in 2002. Large stone markers featuring reliefs of the Korean Peninsula were erected in the median of I-70 in Myersville and Mount Airy in 2004.[4] Along its concurrency with US 40 from I-270 in Frederick to east of West Friendship, I-70 is known as Baltimore National Pike. The Interstate is unnamed from US 40 near West Friendship to its eastern terminus in Baltimore. Like all mainline Interstates, I-70 is a part of the National Highway System for its entire length.[5]

Hancock to Hagerstown

File:Interstate 70 in Western Maryland time-lapse.webm

I-70 enters Washington County concurrent with US 522 from Fulton County, Pennsylvania, north of the town of Hancock. Just south of the state line, the four-lane freeway has a full Y interchange with I-68 and US 40, which head west toward Cumberland as the National Freeway. US 40 begins to run concurrently with I-70 just as US 522 leaves I-70 at another full Y interchange through which I-70 curves to the east. US 522 heads south, providing access to downtown Hancock before crossing the Potomac River into West Virginia. I-70 heads east and gains a lane in each direction to climb a ridge that separates the interchanges from the valley of Tonoloway Creek. The third lane eastbound ends at the top of the ridge and the third lane westbound begins just west of the Interstate's partial interchange with Maryland Route 144 (MD 144, Main Street), which lacks a ramp from MD 144 to westbound I-70.[1][6]

Disambiguation sign posted in advance of the MD 68 interchange on westbound I-70 near Clear Spring

East of MD 144, I-70 parallels the Western Maryland Rail Trail, the Chesapeake and Ohio Canal, and the Potomac River while heading east along a narrow corridor between the river and several north–south ridges. Within this corridor, the freeway has a pair of partial interchanges with MD 615 (Millstone Road). West of Indian Springs, the valley opens up, and US 40 leaves the Interstate at a partial interchange just west of Licking Creek. I-70 continues to parallel the canal and rail trail at a distance until its diamond interchange with MD 56 (Big Pool Road) at Big Pool, where the freeway curves away from the Potomac River and passes to the south of Stone Quarry Ridge and Boyd Mountain. Just south of Clear Spring, I-70 crosses Toms Run within its diamond interchange with MD 68 (Clear Spring Road). Signs on westbound I-70 prior to the MD 68 interchange remind motorists they should remain on I-70 to access I-68.[1][6]

I-70 continues east through the Hagerstown Valley, where the highway crosses over Little Conococheague Creek, Meadow Brook Creek, and Conococheague Creek before reaching a diamond interchange with MD 63 (Greencastle Pike) south of Huyett. As the Interstate approaches Hagerstown, it crosses a branch of Conococheague Creek and CSX's Lurgan Subdivision ahead of its cloverleaf interchange with I-81 (Maryland Veterans Memorial Highway). I-70 heads southeast through the interchange, which has collector–distributor lanes in both directions that separate the individual ramps from the main roadways of both Interstates. The freeway traverses US 11 (Virginia Avenue) and the Winchester and Western Railroad before it curves to the east again. The Interstate has partial cloverleaf interchanges with MD 632 (Downsville Pike) and MD 65 (Sharpsburg Pike) around a crossing of Norfolk Southern Railway's Hagerstown District rail line. I-70 crosses over Antietam Creek and US 40 Alternate (US 40 Alt., Boonsboro Pike) south of Funkstown.[1][6]

Hagerstown to Mount Airy

I-70/US 40 westbound approaching its junction with I-270 and US 15 near Frederick, where US 40 splits from I-70

I-70 meets US 40 (National Pike) at a cloverleaf interchange as the two highways leave the suburban area surrounding Hagerstown. The Interstate curves to the southeast and has a diamond interchange with MD 66 (Mapleville Road) near Beaver Creek. I-70 crosses Beaver Creek and Black Rock Creek and gains an eastbound climbing lane as the highway ascends South Mountain and passes through Greenbrier State Park. At the top of the mountain, the Interstate passes under US 40 and the Appalachian Trail and enters Frederick County.[1][6] I-70 has a pair of rest areas on the east side of the mountain, one per direction.[7] The westbound rest area is where the DC snipers, John Allen Muhammad and Lee Boyd Malvo, were apprehended by police in October 2002.[8]

I-70's eastbound climbing lane disappears and the Interstate has a westbound climbing lane from the top of the mountain southeast to a diamond interchange with MD 17 (Myersville Middletown Road) south of Myersville, where the freeway enters the Middletown Valley. Within the valley, the Interstate crosses Catoctin Creek and Little Catoctin Creek. I-70 gains an eastbound climbing lane as it climbs Braddock Mountain, on top of which the freeway passes under a concrete arch bridge carrying Ridge Road. Westbound I-70 has a climbing lane as the highway descends Braddock Mountain and has partial interchanges with US 40 (National Pike) and US 40 Alt. (Old National Pike). The first interchange is a pair of flyover ramps from eastbound I-70 to eastbound US 40 and from westbound US 40 to westbound I-70. The second interchange is a half diamond interchange with an exit ramp from westbound I-70 to US 40 Alt. and an entrance ramp to eastbound I-70.[1][6]

After entering the Frederick Valley, I-70's speed limit drops from 70 to 65 mph (113 to 105 km/h). The Interstate passes under MD 180 (Jefferson Pike) and has a partial interchange with Jefferson National Pike, a freeway that carries US 15 and US 340; eastbound I-70 has ramps to both eastbound and westbound US 15/US 340, while westbound I-70 has only a flyover ramp to westbound Jefferson National Pike. Eastbound I-70 receives a ramp from MD 180 and Ballenger Creek Pike and crosses over the state highway before reaching a directional interchange with I-270 and US 40. I-270 heads south toward Washington, DC, as the Eisenhower Memorial Highway, taking over the name from I-70, while US 40 (Frederick Freeway) exits to the north and joins I-70 in a concurrency. I-70 heads east as a six-lane freeway and meets MD 85 (Buckeystown Pike) at a single-point urban interchange (SPUI) south of downtown Frederick. MD 85 is used to access MD 355 (Urbana Pike). The Interstate reduces to four lanes before it crosses over the Frederick Branch of CSX's Old Main Line Subdivision. On the east side of Frederick, I-70 has a four-ramp partial cloverleaf interchange with South Street and a partial diamond interchange with MD 144 (Patrick Street).[1][6]

I-70 heads east from the Frederick area as a six-lane freeway with a speed limit of 70 mph (110 km/h). The Interstate crosses over the Monocacy River and Long Spring Branch ahead of a partial interchange with MD 144 (Old National Pike), which includes ramps from westbound I-70 to westbound MD 144 and eastbound MD 144 to eastbound I-70. County-maintained Old National Pike parallels the north side of the Interstate east to Mount Airy via New Market, where I-70 has a diamond interchange with MD 75 (Green Valley Road). East of New Market, the freeway is also paralleled by the Old Main Line Subdivision as the highways and rail line follow the valley of Bush Creek to just west of Mount Airy. I-70 veers southeast for its partial cloverleaf interchange with MD 27 (Ridge Road) at the top of Parr's Ridge on the Frederick–Carroll county line.[1][6]

Mount Airy to Woodlawn

I-70/US 40 in western Howard County

I-70 is closely paralleled by MD 144 (Frederick Road) on its eastbound side as the freeway briefly passes through Carroll County. The Interstate enters Howard County when it traverses the South Branch of the Patapsco River near its headwaters. MD 144 leaves the vicinity of I-70, which meets MD 94 (Woodbine Road) at a diamond interchange in Lisbon and MD 97 (Roxbury Mills Road) at another diamond interchange near Cooksville. East of their diamond interchange with MD 32 (Sykesville Road), I-70 and US 40 split at a partial interchange. I-70 heads east as a four-lane freeway toward Baltimore while US 40 heads east as four-lane Baltimore National Pike to serve Ellicott City. Just east of the US 40 split, the Interstate has a partial interchange with Marriottsville Road that allows westbound I-70 to access US 40.[1][6]

North of Ellicott City, I-70 has a cloverleaf interchange with US 29 (Columbia Pike) just south of the U.S. Route's northern terminus at MD 99 (Old Frederick Road) and Rogers Avenue, which heads south toward the Ellicott City Historic District. The interchange includes a flyover ramp from westbound I-70 to southbound US 29. The Interstate continues east as a six-lane freeway through Patapsco Valley State Park, where the highway crosses the Patapsco River and the Old Main Line Subdivision again and enters Baltimore County. As the freeway approaches the suburb of Woodlawn, the speed limit decreases to 55 mph (89 km/h).[1][6] The westbound direction has a mileage sign with approximate values for Columbus, Ohio; St. Louis, Missouri; Denver, Colorado; and the small town of Cove Fort, Utah, at the opposite end of I-70. This sign, which was intended as a test of Clearview typeface, was installed in 2004.[9][10] I-70 reaches its eastern terminus at its four-level stack interchange with I-695 (Baltimore Beltway).[11] West of the interchange, the freeway has an average traffic value of 94,221 vehicles.[1][6]

Woodlawn to Baltimore

"Maryland Route 570" redirects here. For the former highway, see Maryland Route 570 (former).

Maryland Route 570

LocationWoodlawn–Baltimore
Length1.95 mi[12] (3.14 km)
Existed2020–present

East of the interchange, MD 570 (which is still signed as I-70) continues as a four-lane highway for local traffic that averages 25,300 vehicles per day. The route's speed limit reduces to 40 mph (64 km/h) and then 25 mph (40 km/h) as it passes through its final interchange, a partial cloverleaf junction with MD 122 (Security Boulevard), which continues southeast into Baltimore as Cooks Lane.[1][6] Just east of the interchange, MD 570 enters the city of Baltimore and the freeway's median expands into a park and ride facility that is accessed at the freeway's eastern terminus at a U-turn adjacent to Gwynns Falls/Leakin Park. Eastbound MD 570 traffic that wishes to access Cooks Lane has to make a U-turn at the terminus and exit from a westbound loop ramp. Westbound access to MD 570 is done via a single entrance ramp off Ingleside Avenue, which is considered part of the MD 122 interchange. The very short section of MD 570 in the city of Baltimore is maintained by the Baltimore City Department of Transportation instead of the Maryland State Highway Administration (MDSHA).[2][6]

History

Interstate 70N

LocationFrederick–Baltimore
Existed1966–1974
NHSEntire route

I-70 was planned to follow the US 40 corridor from Hancock east to Frederick, where the Interstate Highway designation split. I-70N would continue following US 40 east to Baltimore while I-70S would follow US 240 southeast toward Washington. In 1974, the suffixed designations were eliminated; I-70N became an eastward extension of I-70 while I-70S was designated I-270.[9][13]

Baltimore National Pike and Frederick Freeway

View east along I-70/US 40 (Baltimore National Pike) near Lisbon

The first section of I-70 in Maryland was constructed as Baltimore National Pike, a four-lane divided highway relocation and reconstruction of US 40 from the Pine Orchard community west of Ellicott City west to the east end of Patrick Street in Frederick. US 40 was constructed from Pine Orchard to MD 32 in West Friendship between 1949 and 1951. An overpass of MD 32 and two-way ramp connection between the two highways were constructed in 1951 and 1952. An overpass and connecting ramp were also constructed at MD 97, which was included in the portion of US 40 constructed from West Friendship to Morgan Station Road west of Cooksville between 1950 and 1952.[14] The third section of Baltimore National Pike was built from Morgan Station Road into Carroll County just west of the Patapsco River in 1952 and 1953.[14][15][16] The next section of relocated US 40, from west of the Patapsco River through the Ridgeville section of Mount Airy into Frederick County 0.5 miles (0.80 km) west of MD 27, broke ground in 1953 and was completed by 1955.[15][17] An interchange with MD 27 in Ridgeville was constructed in 1953 and 1954.[15]

The remainder of Baltimore National Pike from Ridgeville to the Monocacy River was constructed in four sections simultaneously starting in 1953. The first three sections were from 0.5 miles (0.80 km) west of the Carroll–Frederick county line to the highway's crossing of the Baltimore and Ohio Railroad's main line at a site called Plane No. 4, from there to New Market, and between New Market and Ijamsville Road in Bartonsville.[15] The fourth section was constructed to closely parallel the existing alignment of US 40 from Ijamsville Road in Bartonsville to just east of the Monocacy River. All four sections opened as a divided highway with a macadam surface in 1955. The following year, Baltimore National Pike from Ridgeville to the Monocacy River was completed with an asphalt surface.[15][17][18] The final section of Baltimore National Pike, from east of the Monocacy River to the east end of Patrick Street near modern exit 56, was expanded to a divided highway in 1953 with the exception of the Monocacy River crossing. Engineering work on a second bridge across the Monocacy River began in 1954.[15] The new bridge, which would complement the existing bridge that had been constructed in 1944 to replace the historic Jug Bridge, opened in 1956, completing the Baltimore National Pike.[18][19][20]

The western end of Baltimore National Pike was planned to tie into both Patrick Street and the eastern end of the Frederick Freeway, which would serve as a US 40 freeway bypass of downtown Frederick between its two interchanges with Patrick Street. Construction on the east–west US 40 portion of the Frederick Freeway began in 1954 and was completed by 1958.[15][18][21] Old US 40 through downtown Frederick later became part of MD 144. The freeway's original interchanges along what is now I-70 included a partial interchange with Patrick Street east of Frederick, the present interchange at South Street, folded diamond interchanges at MD 355 and New Design Road, and a partial interchange with Washington National Pike (now I-270), where the Frederick Freeway curved north to cloverleaf interchanges with US 340 and the western end of Patrick Street.[21] The north–south portion of the Frederick Freeway was completed in 1959 and became part of US 15.[22] The Frederick Freeway was marked with exit numbers in 1963; the portion that is part of I-70 started from exit 1 at MD 144 east of Frederick and went to exit 4 at New Design Road.[23]

Interstate construction and upgrades

The next section of US 40 and future I-70 to be upgraded was east of Hancock. US 40 was reconstructed as a divided highway from Tonoloway Creek at the eastern end of Hancock parallel to the Potomac River to the community of Millstone at what is now the southern terminus of MD 615 in 1961.[24] This piece of highway became the first completed section of highway in Maryland to be marked as I-70 in 1962.[25] In 1964, construction began on I-70 from the western end of the existing highway to the Pennsylvania state line.[26] This project happened concurrently with the construction of what is now I-68 west from I-70 to MD 144 west of Hancock; both projects were completed in 1966.[26][27] Construction of I-70 from Hancock to Frederick was fully underway in an eastward direction by 1965.[28] The Interstate opened from MD 615 to MD 56 in 1965;[28] from MD 56 to MD 68 in 1966;[27] from MD 68 to I-81 in 1967;[29] from I-81 to US 40 east of Hagerstown in 1968;[30] and from US 40 to the Frederick Freeway in 1969.[31] When the interchange between the Frederick Freeway and Washington National Pike was reconstructed to add I-70 toward Hagerstown in 1969, the freeway's interchange with New Design Road was removed.[31] Exit numbers were added to I-70 from Hancock to Frederick in 1974.[13]

I-70 westbound in Hancock

I-70 was constructed on a new alignment from east of West Friendship to Baltimore. The Interstate opened in 1967 from US 29 to I-695, concurrent with US 29's northward extension from US 40 to MD 99.[29] I-70 opened from US 40 in West Friendship to US 29 and from I-695 to Security Boulevard just west of the Baltimore city line in 1969.[31] I-70 was upgraded to Interstate standards from Bartonsville to West Friendship around 1974. Diamond interchanges were constructed to replace at-grade intersections with MD 94 and MD 75; for the latter interchange, MD 75 was relocated east of New Market. The existing interchanges at MD 32 and MD 97 were converted from two-way connector ramps to diamond interchanges.[13] I-70's interchange with MD 27 was expanded from a four-ramp partial cloverleaf to a six-ramp partial cloverleaf in 1977.[32] Exit numbers were added east of Frederick in 1978; however, these exit numbers were each 2 less than the present numbers, which were marked in 1983.[33][34] I-70 was relocated away from the original alignment of US 40 between its junctions with MD 144 in Frederick and Bartonsville around 1987; the old highway became an eastern extension of MD 144.[35] Outside of the reconstruction of the Interstate through Frederick beginning in the 1990s, there have been two interchanges revised or added, both near Hagerstown. A direct ramp was added from eastbound I-70 to southbound MD 65 in 1995; this interchange had four ramps, including two loop ramps with eastbound I-70, from at least 1968.[30][36] I-70's interchange with MD 632 opened in 1999.[37]

In Washington County, MDOT SHA reconstructed and widened I-70's bridges over Conococheague Creek starting in summer 2012.[38] The reconstruction of the bridges was completed in July 2014.[39]

In Frederick County, MDOT SHA upgraded I-70's partial interchange with MD 144 in Bartonsville, which only had ramps from westbound I-70 to westbound MD 144 and from eastbound MD 144 to eastbound I-70.[40] A ramp from Meadow Road to westbound I-70 was opened in October 2019.[41] In August 2022, MD 144 was reconfigured and widened to four lanes from Baltimore Road to east of Meadow Road, and a ramp was constructed from eastbound I-70 to MD 144.[42]

Reconstruction through Frederick

In 1984, MDOT SHA completed the I-70 Corridor Planning Study, which examined the 5.3-mile (8.5 km) segment of I-70 from the Mount Philip Road overpass between Braddock Mountain and Frederick to just east of MD 144 at the western end of the project underway to relocate the Interstate through Bartonsville.[43][44] The study proposed a series of projects to upgrade I-70 through Frederick, much of which had been constructed as the Frederick Freeway in the late 1950s, to Interstate standards. The four-lane freeway was plagued with closely spaced interchanges with substandard acceleration and deceleration lanes and curve radii. Many of the interchanges were missing important movements between highways. For instance, travelers aiming to move from southbound US 15 to westbound I-70 needed to use US 40 through Frederick's heavily commercialized Golden Mile to join I-70 at exit 48.[44]

The first project involved I-70's interchange with US 15 and US 340, which was constructed with two ramps, one from westbound I-70 to southbound US 15 and one from northbound US 15 to eastbound I-70, in 1969.[31][44] In this project completed in 1997, two ramps were added from eastbound I-70 to both directions of US 15; a long ramp was added that started from northbound US 15 and eastbound US 40 at their interchange to provide access to westbound I-70; and a loop ramp from MD 180 and MD 351 (Ballenger Creek Pike) to eastbound I-70 between I-70's interchanges with US 15 and I-270.[45][46] The second project filled in a pair of missing connections to the I-70/I-270 interchange last updated in 1969.[31][44] Ramps were added from westbound I-70 to southbound I-270 and from northbound I-270 to eastbound I-70; in addition, New Design Road received a new bridge over I-70 and I-270. After the second project was completed in 2002, traffic between I-70 from the east and I-270 from the south no longer needed to use MD 355 and MD 85 to make the connections.[46][47][48]

The third project was the replacement of I-70's interchange with MD 355, a four-ramp partial cloverleaf interchange constructed in 1956.[20] In 2001, westbound I-70's ramps with MD 355 were closed and replaced with temporary ramps to and from Stadium Drive, which connected the freeway with the state highway.[49] In 2005, as part of a related project, the MD 85/MD 355 intersection was reconstructed and MD 85 was extended to a temporary terminus east of MD 355 at a pair of ramps with eastbound I-70. Eastbound I-70's existing ramps at MD 355 were closed.[2] As part of the project, East Street was extended south from downtown Frederick to I-70's SPUI with MD 85, which was completed in 2009. Once the new interchange opened, the temporary ramps between westbound I-70 and Stadium Drive were removed.[50]

The fourth project to upgrade I-70 through Frederick, which will upgrade the interchanges at South Street and MD 144 built in 1956, began in autumn 2010.[20][51] Eastbound I-70's ramps with Reichs Ford Road, which leads to South Street, will be reconstructed. The westbound ramps serving South Street will be removed. The missing movements on the eastern end of Frederick will be provided by reconstruction of westbound I-70's ramps with MD 144. A ramp from MD 144 to westbound I-70 will be added; both that ramp and the exit ramp from westbound I-70 will meet MD 144 at a roundabout. Once the interchanges are reconstructed, I-70 will be expanded to six lanes from east of MD 144 to I-270.[51] The fifth and final project to upgrade I-70 through Frederick will expand I-70 to six lanes between Mount Philip Road and I-270.[43]

Future

In Howard County, as part of the upgrade of MD 32 to a freeway from MD 108 to I-70, the state highway's junction with I-70 will be reconstructed from a diamond interchange to a partial cloverleaf design that will allow free-flowing traffic from both directions of MD 32 onto I-70.[52] In Howard County, a study is underway concerning improvements to the portion of I-70 between MD 32 and US 29; between the US 40 split and US 29, I-70 is only four lanes. The study will look at widening the Interstate to six or eight lanes as well as possible improvements on US 29 and Marriottsville Road at their respective interchanges with I-70.[53] In Baltimore and Howard counties, a study is underway in consideration of widening I-70 between I-695 and US 29 to eight or possibly 10 lanes. This would require the reconstruction of the bridges over the Patapsco River in both directions in order to accommodate more lanes.

Highway in Baltimore

Early freeway plans for Baltimore

Nine plans for a Baltimore city freeway system were put together by Baltimore city planners between 1942 and 1957.[54] The most influential of these plans was portrayed in the Smith Report of 1945, which heavily influenced future proposals, including the proposal that would be included in the General Location of National System of Interstate Highways, also known as the Yellow Book, in 1955.[55] None of the plans gained traction due to either decision makers figuring the freeways were not needed or opposition to the east–west freeway passing straight through the central business district or immediately to the north of the central business district.[54] For instance, a 1957 proposal had the east–west freeway following Biddle Street through the northern part of Downtown Baltimore.[56]

Planning map for the Baltimore freeways from the 1955 Yellow Book

However, by the late 1950s, Baltimore was starting to suffer from the flight of its commercial and industrial concerns and residents to the suburbs in response to the easy access provided by the developing Baltimore Beltway.[54] In response to the new sense of urgency, the head of Baltimore's Department of Planning, Philip Darling, put together a 1960 report titled A Study for an East–West Expressway.[54] Darling proposed I-70N pass through Gwynns Falls/Leakin Park and the Rosemont neighborhood and head east between Franklin Street and Mulberry Street. The East–West Expressway would turn south near Pine Street and turn east again to follow an elevated highway just south of Pratt Street, between the central business district and the Inner Harbor. At the east end of the Inner Harbor, at approximately the modern intersection of President Street and Eastern Avenue, I-70N would reach its terminus at a four-way interchange with I-83 (Jones Falls Expressway) and I-95 (Southwestern Expressway). I-95 would cross the Inner Harbor on a 50-foot-high (15 m) bridge immediately to the southwest of the interchange.[56]

The 10-D and 3-A systems

Darling's outreach with various civic groups meant there was little opposition to the proposed route of the East–West Expressway. The last obstacle before the freeway could receive federal funding was a review by independent consultants. A group of three consulting firms that came together as Expressway Consultants reviewed Darling's plan and made major changes without consulting the civic groups Darling had engaged. As a result, when the consultants released their 10-D System in 1962, the plan faced widespread opposition.[54] In the 10-D System, I-70N would follow roughly the same route as in the Darling Plan east to Fremont Avenue. There, the freeway would follow Fremont Avenue south to a junction with I-95 at Hamburg Street.[57] The route of the East–West Expressway in the 10-D System would require condemning a greater number of properties compared to Darling's plan due to I-70N and I-95 passing through several residential neighborhoods south of the central business district. Several of the civic groups with which Darling had compromised opposed Expressway Consultants's uncompromising position toward their route through Leakin Park.[54]

Despite the major opposition, the initiation of federal funding allowed the city to start acquiring property in the Franklin–Mulberry corridor in 1966 to clear the way for construction of the stretch of freeway that did get built between Pulaski Street and Martin Luther King Jr. Boulevard. That same year, the city of Baltimore decided to resolve the deadlock on the 10-D System by forming another consulting group, Urban Design Concept Associates, to work with various experts and stakeholders to come up with a new, less disruptive freeway system proposal for Baltimore. In 1969, the city adopted the group's proposal for the 3-A System.[54] I-70N would pass through Gwynns Falls/Leakin Park, then follow Gwynns Falls south to an interchange with the modern alignment of I-95 east of Caton Avenue. Another freeway, later designated I-170, would be constructed in the Franklin–Mulberry corridor to connect I-70 with the west side of the central business district.[58]

However, many of the civic groups still opposed I-70 passing through Gwynns Falls/Leakin Park; the groups used litigation and political will to indefinitely delay the construction of I-70 through the park.[54] In 1981, the city canceled the portion of I-70 from its current eastern terminus through Gwynns Falls/Leakin Park to the Interstate's interchange with I-170. I-170 and the portion of proposed freeway south to I-95 remained part of plans with a new designation for the L-shaped freeway, I-595.[9] However, in 1983, I-595 was canceled as well due to escalating costs; saving funds for the original I-595 freeway would detract from more pressing needs like maintenance of city streets and rapid transit.[9][54] I-595 was later used as an unsigned designation for the upgrade of US 50 between the Capital Beltway and Annapolis.[1] With the abandonment of I-70's extension further into the city, the Baltimore City Department of Transportation converted the Interstate's stub end east of Security Boulevard (MD 122) into a park and ride facility that opened in September 1985.[55] At the once-planned I-95 interchange, a flyover ramp that was to become the ramp from eastbound I-70 to southbound I-95 was demolished in 1997, though several other ramp stubs remain in place.

Route description of I-70 in the 3-A System

Eastern terminus of MD 570 (former I-70) at park and ride lot in Baltimore

Had I-70 been constructed as planned in the 3-A System, I-70 would have continued east from its present terminus just west of the Baltimore city limits near Security Boulevard. The Interstate would curve to the northeast and traverse Dead Run and Franklintown Road, then pass through a short tunnel underneath a hill in Leakin Park. I-70 would curve east through Gwynns Falls Park, where the freeway would cross over Dead Run and Franklintown Road again just south of the stream's confluence with Gwynns Falls. The Interstate would parallel Gwynns Falls southeast to an interchange with Hilton Parkway, a four-lane divided highway that connects the portions of Hilton Street on either side of the Gwynns Falls valley. The directional T interchange would provide access from both directions of I-70 to northbound Hilton Parkway and from southbound Hilton Parkway to I-70. I-70 would continue south while paralleling Hilton Parkway on the east until the freeway's underpass of US 40 (Edmondson Avenue).[58]

I-70 would have continued southeast along Gwynns Falls and what is now CSX's Hanover Subdivision. The Interstate would have met the western end of I-170 at a directional T interchange where Baltimore Street and Amtrak's Northeast Corridor cross over Gwynns Falls. I-170 would have headed northeast closely paralleling the Amtrak Northeast Corridor before veering east at the West Baltimore station on MARC's Penn Line to join the constructed portion of I-170, which is now part of US 40. I-70 would have continued southeast to a partial interchange with MD 144 (Frederick Avenue) that would have allowed access to and from the direction of I-95. The Interstate would have passed under US 1 (Wilkens Avenue) before reaching its terminus at I-95. I-70's junction with I-95 would have been a directional T interchange constructed over a rail yard on the Mount Clare Branch of CSX's Baltimore Terminal Subdivision.[58] When I-95 was completed from Caton Avenue to Russell Street in February 1978, the highway was paralleled by extended ramps east from the Caton Avenue interchange that would have allowed connections between I-70 and Caton Avenue (US 1 Alt.) and segregated I-70 and Caton Avenue traffic from the partial interchange with Washington Boulevard just to the east.[55]

Truncation of eastern terminus

The 1.95-mile (3.14 km) extension beyond I-695 to the I-70 park and ride facility was formally dropped from the Interstate Highway System in August 2014 after approvals from the American Association of State Highway and Transportation Officials (AASHTO)[12] and the Federal Highway Administration (FHWA)[59] but remains signed as I-70.[60] In 2020, the former alignment of I-70 between I-695 and the park and ride lot became designated as MD 570.[61]

Exit list

CountyLocationmi
[1][2]		kmExitDestinationsNotes
WashingtonHancock0.000.00

 I-70 west / US 522 north – Breezewood		Continuation into Pennsylvania
0.631.011A
 I-68 / US 40 west (National Freeway) – Cumberland		Western end of US 40 concurrency; eastern end of US 522 concurrency; eastern terminus of I-68; I-70, US 40, and US 522 are mutually concurrent with each other in westbound lanes only; I-68 exits 82B–C
1.161.871B
 US 522 south (Warfordsburg Road) – Hancock, Winchester
3.515.653
 MD 144 west / Historic National Road / C&O Canal Scenic Byway – Hancock		Left exit westbound; no westbound entrance
​4.417.105 MD 615 (Millstone Road)Eastbound exit and westbound entrance
​5.869.43
 MD 615 north (Millstone Road)		Westbound exit and eastbound entrance
Pecktonville9.1814.779
 US 40 east / Historic National Road – Indian Springs		Eastbound exit and westbound entrance; east end of US 40 concurrency
Big Pool11.9719.2612 MD 56 (Big Pool Road) / C&O Canal Scenic Byway – Big Pool, Indian Springs
Clear Spring17.6228.3618 MD 68 (Clear Spring Road) – Clear Spring
Wilson-Conococheague24.1138.8024 MD 63 (Greencastle Pike) – Williamsport, Huyett
Halfway25.7241.3926 I-81 (Maryland Veterans Memorial Highway) – Roanoke, HarrisburgI-81 exit 4; cloverleaf interchange with collector–distributor lanes
27.7544.6628 MD 632 (Downsville Pike) – Hagerstown, Downsville
Hagerstown29.1046.8329 MD 65 (Sharpsburg Pike) – Sharpsburg, HagerstownSplit into exits 29A (south) and 29B (north) eastbound
31.6850.9832 US 40 (National Pike) – HagerstownSplit into exits 32A (east) and 32B (west)
Mount Aetna34.2755.1535 MD 66 (Mapleville Road) – Smithsburg, Boonsboro
FrederickMyersville41.9267.4642 MD 17 (Myersville Middletown Road) – Myersville, Middletown
Braddock Heights48.7978.5248
 US 40 east (Baltimore National Pike) – Frederick		Eastbound exit and westbound entrance
49.0778.9749
 US 40 Alt. (Old National Pike) – Braddock Heights, Middletown		Westbound exit and eastbound entrance
Frederick52.0983.8352A

 US 15 south / US 340 west – Charles Town, Leesburg		Signed as exit 52 westbound; eastbound entrance includes direct entrance ramp from Ballenger Creek Pike ( MD 180)
52B
 US 15 north (US 340 east) – Gettysburg		Eastbound exit only; westbound access via exit 53B
52.9885.2653A
 I-270 south (Washington National Pike) – Washington		Signed as exit 53 eastbound
53B


 US 40 west to US 15 north (Frederick Freeway) – Gettysburg		West end of US 40 concurrency; no eastbound exit
54.1487.1354
 MD 85 (Buckeystown Pike) to MD 355 (Urbana Pike) – Buckeystown		Single-point urban interchange
54.6988.0255South Street
55.2288.8756 MD 144 (Patrick Street)Westbound entrance accessible by police vehicles only
Bartonsville58.5894.2859 MD 144 (Old National Pike) – Linganore, Ijamsville
New Market62.29100.2562 MD 75 (Green Valley Road) – Libertytown, Hyattstown
CarrollMount Airy67.73109.0068 MD 27 (Ridge Road) – Damascus, Mount Airy
HowardLisbon73.12117.6873 MD 94 (Woodbine Road) – Woodbine, Lisbon
Cooksville76.29122.7876 MD 97 (Hoods Mill Road) – Westminster, Olney
West Friendship79.96128.6880 MD 32 (Sykesville Road) – Clarksville, Sykesville
82.08132.0982
 US 40 east (Baltimore National Pike east) – Ellicott City		Eastbound exit and westbound entrance; east end of concurrency with US 40
82.90133.4183Marriottsville RoadWestbound exit and eastbound entrance
Ellicott City86.99140.0087
 US 29 (Columbia Pike) to MD 99 – Columbia, Washington		Split into exits 87A (south) and 87B (north); US 29 exit 25
BaltimoreWoodlawn91.67147.5391
 I-695 (Baltimore Beltway) to I-95 – Glen Burnie, Towson, Baltimore, New York		Stack interchange; split into exits 91A (south) and 91B (north); I-695 exits 16A–B; eastern terminus of I-70;[12] western terminus of MD 570
93.44150.3894
 MD 122 west (Security Boulevard) / Cooks Lane south		No direct eastbound access to Cooks Lane
Baltimore City93.62150.67 Park and RideEastern terminus of MD 570
1.000 mi = 1.609 km; 1.000 km = 0.621 mi

Auxiliary routes

I-70 has two auxiliary Interstate Highways in Maryland.

Interstate 270

Main article: Interstate 270 (Maryland)

Interstate 270

LocationBethesda–Frederick
Length34.70 mi[1] (55.84 km)
Existed1975–present
NHSEntire route

Interstate 270 (I-270) is a 34.70-mile (55.84 km) auxiliary Interstate Highway in the US state of Maryland that travels between I-495 (Capital Beltway) just north of Bethesda in Montgomery County and I-70/US 40 in the city of Frederick in Frederick County. It consists of the 32.60-mile (52.46 km) mainline as well as a 2.10-mile (3.38 km) spur that provides access to and from southbound I-495. I-270 is known as the Dwight D. Eisenhower Memorial Highway as well as the Washington National Pike. Most of the southern part of the route in Montgomery County passes through suburban areas around Rockville and Gaithersburg that are home to many biotech firms.[62] This portion of I-270 is up to 12 lanes wide and consists of a local–express lane configuration as well as high-occupancy vehicle lanes (HOV lanes) that are in operation during peak travel times. North of the Gaithersburg area, the road continues through the northern part of Montgomery County, passing Germantown and Clarksburg as a six- to eight-lane highway with an HOV lane in the northbound direction only. North of here, I-270 continues through rural areas into Frederick County and toward the city of Frederick as a four-lane freeway.[1]

Interstate 370

Main article: Interstate 370

Interstate 370

LocationGaithersburg
Length2.54 mi[1] (4.09 km)
Existed1988–present
NHSEntire route

Interstate 370 (I-370) is a 2.54-mile (4.09 km) Interstate Highway spur route off I-270 in Gaithersburg to the western end of MD 200 (Intercounty Connector) at an interchange that provides access to the park and ride lot at the Shady Grove station on the Red Line of the Washington Metro. Despite the number, I-370 does not connect to I-70 itself. The road continues to the west of I-270 as Sam Eig Highway, a surface road. Along the way, I-370 has interchanges with MD 355 and Shady Grove Road.[1] The freeway was completed in the late 1980s to connect I-270 to the Shady Grove Metro station. I-370 was part of the larger Intercounty Connector but was the only segment to be built at the time.[63] MD 200 east of I-370 to MD 28 (Norbeck Road) opened on February 23, 2011, resulting in the truncation of I-370 to the interchange with MD 200 and the redesignation of the road leading into the Shady Grove Metro station as MD 200A.[1][64][65]

References

  1. ^ a b c d e f g h i j k l m n o p q r s Highway Information Services Division (December 31, 2022). Highway Location Reference. Maryland State Highway Administration. Retrieved October 26, 2011.
  2. ^ a b c d Highway Information Services Division (December 31, 2005). Highway Location Reference. Maryland State Highway Administration. Retrieved October 26, 2011.
  3. ^ "Dwight D. Eisenhower Highway". Federal Highway Administration. Retrieved May 5, 2011.
  4. ^ "I-70 tribute to Korean War vets". The Washington Times. May 2, 2004. Retrieved May 5, 2011.
  5. ^ Federal Highway Administration (August 2003). National Highway System: Maryland (PDF) (Map). Scale not given. Federal Highway Administration. Retrieved May 5, 2011.
  6. ^ a b c d e f g h i j k l Google (January 27, 2011). "Interstate 70 in Maryland" (Map). Google Maps. Google. Retrieved January 27, 2011.
  7. ^ "Maryland Welcome Centers and Rest Areas". Maryland State Highway Administration. Retrieved August 16, 2009.
  8. ^ "Police arrest sniper suspects". BBC News. October 24, 2002. Retrieved July 25, 2008.
  9. ^ a b c d "Why Does I-70 End in Cove Fort, Utah?". Ask the Rambler. Highway History. Federal Highway Administration. December 29, 2008. Retrieved May 3, 2009.
  10. ^ Nitzman, Alex (August 7, 2004). "Cove Fort Mileage Sign" (JPG). AARoads. Retrieved May 11, 2011.
  11. ^ Nitzman, Alex (June 17, 2000). "I-70 Ends Sign" (JPG). AARoads. Retrieved May 11, 2011.
  12. ^ a b c Special Committee on U.S. Route Numbering (May 29, 2014). "Report to SCOH" (Report). Washington, DC: American Association of State Highway and Transportation Officials. Archived from the original (DOCX) on February 26, 2020. Retrieved April 4, 2018.
  13. ^ a b c Maryland State Highway Administration (1974). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Highway Administration. Central Maryland inset.
  14. ^ a b McCain, Russell H.; Hall, Avery W.; Nichols, David M. (December 15, 1952). Report of the State Roads Commission of Maryland (1951–1952 ed.). Baltimore: Maryland State Roads Commission. pp. 140, 144–145. Retrieved May 12, 2011.
  15. ^ a b c d e f g McCain, Russell H.; Bennett, Edgar T.; Kelly, Bramwell (November 12, 1954). Report of the State Roads Commission of Maryland (1953–1954 ed.). Baltimore: Maryland State Roads Commission. pp. 215, 218–219, 222. Retrieved May 12, 2011.
  16. ^ Maryland State Roads Commission (1953). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission.
  17. ^ a b Maryland State Roads Commission (1955). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission.
  18. ^ a b c Bonnell, Robert O.; Bennett, Edgar T.; McMullen, John J. (November 2, 1956). Report of the State Roads Commission of Maryland (1955–1956 ed.). Baltimore: Maryland State Roads Commission. pp. 4, 205. Retrieved May 12, 2011.
  19. ^ Whitman, Ezra B.; Webb, P. Watson; Thomas, W. Frank (March 1, 1945). Report of the State Roads Commission of Maryland (1943–1944 ed.). Baltimore: Maryland State Roads Commission. p. 101. Retrieved May 12, 2011.
  20. ^ a b c Maryland State Roads Commission (1956). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission.
  21. ^ a b Maryland State Roads Commission (1958). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission.
  22. ^ Maryland State Roads Commission (1959). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission.
  23. ^ Maryland State Roads Commission (1963). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission.
  24. ^ Maryland State Roads Commission (1961). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission.
  25. ^ Maryland State Roads Commission (1962). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission.
  26. ^ a b Maryland State Roads Commission (1964). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission. § A9.
  27. ^ a b Maryland State Roads Commission (1966). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission. §§ A9–A10.
  28. ^ a b Maryland State Roads Commission (1965). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission. §§ A9–A11, B11–B12, C13.
  29. ^ a b Maryland State Roads Commission (1967). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission. §§ A10–A11, D16–D17.
  30. ^ a b Maryland State Roads Commission (1968). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission. Hagerstown inset. §§ A11, B11–B12.
  31. ^ a b c d e Maryland State Roads Commission (1969). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Roads Commission. Frederick inset. §§ B12, C13, D16–D17.
  32. ^ Maryland State Highway Administration (1977). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Highway Administration. Central Maryland inset.
  33. ^ Maryland State Highway Administration (1978). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Highway Administration. §§ C13–C15, D15–D17.
  34. ^ Maryland State Highway Administration (1983). Maryland: Official Highway Map (PDF) (Map) (1983–1984 ed.). Baltimore: Maryland State Highway Administration. §§ C13–C15, D15–D17.
  35. ^ Maryland State Highway Administration (1987). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Highway Administration. §§ C13–C14.
  36. ^ Maryland State Highway Administration (1995). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Highway Administration. Hagerstown inset.
  37. ^ Maryland State Highway Administration (1999). Maryland: Official Highway Map (PDF) (Map) (1999–2000 ed.). Baltimore: Maryland State Highway Administration. Hagerstown inset.
  38. ^ "Project Information: IS 0070 Eisenhower Memorial Highway Dual Bridges 21106 over Conococheague Creek". Maryland State Highway Administration. Retrieved May 13, 2011.
  39. ^ "Rehabilitation Of I-70 Bridges Over Conococheague Creek Nears Completion" (Press release). Maryland State Highway Administration. July 15, 2014. Retrieved April 12, 2022.
  40. ^ "Project Information: IS 0070 Baltimore National Pike at Meadow Road: Ijamsville Road Interchange Study". Maryland State Highway Administration. Retrieved May 13, 2011.
  41. ^ Marshall, Ryan (October 1, 2019). "I-70 ramp opens at Meadow Road". The Frederick News-Post. Retrieved January 18, 2024.
  42. ^ "Lake Linganore | I-70 at Meadow Road Interchange". Lake Linganore. Retrieved January 18, 2024.
  43. ^ a b "Project Information: IS 0070 West of I-270 to Mt Phillip Road (Phase 4)". Maryland State Highway Administration. Retrieved May 13, 2011.
  44. ^ a b c d "Purpose and Need: I-70" (DOC). Maryland State Highway Administration. 1984. Retrieved May 13, 2011.
  45. ^ Maryland State Highway Administration (1997). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Highway Administration. Frederick inset.
  46. ^ a b "I-70 Frederick Area Improvements Project: Spring 2007 Newsletter" (PDF). Maryland State Highway Administration. Spring 2007. Retrieved May 13, 2011.
  47. ^ Maryland State Highway Administration (2002). Maryland: Official Highway Map (PDF) (Map). Baltimore: Maryland State Highway Administration. Frederick inset.
  48. ^ Highway Information Services Division (December 31, 2002). Highway Location Reference. Maryland State Highway Administration. Retrieved October 26, 2011.
  49. ^ Highway Information Services Division (December 31, 2001). Highway Location Reference. Maryland State Highway Administration. Retrieved October 26, 2011.
  50. ^ Highway Information Services Division (December 31, 2009). Highway Location Reference. Maryland State Highway Administration. Retrieved October 26, 2011.
  51. ^ a b "Project Information: IS 0070 Baltimore National Pike TC-Phase 2D: East of Patrick Street (MD 144) to West of MD 355". Maryland State Highway Administration. Retrieved May 13, 2011.
  52. ^ "Project Information: MD 0032 Patuxent Freeway MD 108 to I-70". Maryland State Highway Administration. Retrieved May 13, 2011.
  53. ^ "Project Information: IS 0070 MD 32 to US 29". Maryland State Highway Administration. Retrieved May 13, 2011.
  54. ^ a b c d e f g h i Wikberg, Terry (2000). "Building Baltimore: The Baltimore City Interstate Highway System" (PDF). University of Maryland School of Law. Retrieved May 12, 2011.
  55. ^ a b c "Major Transportation Milestones in the Baltimore Region Since 1940" (PDF). Baltimore Metropolitan Council. December 1, 2005. pp. 2, 8, 10. Archived from the original (PDF) on December 27, 2010. Retrieved May 12, 2011.
  56. ^ a b Department of Planning (January 1960). A Study for an East–West Expressway. Baltimore: City of Baltimore.
  57. ^ Expressway Consultants (1961). Interstate Highways 70N and 95, the East–West and Southwest Expressways, Baltimore, Maryland, Preliminary Engineering Report. a joint corporate venture of J. E. Greiner Company, Inc.; Remmer, Klepper & Kahl; and Knoerle, Graef, Bender & Associates. Baltimore: Department of Public Works, City of Baltimore.
  58. ^ a b c Urban Design Concept Associates (December 1970). Final Joint Development, Baltimore Interstate Highway System 3-A. a joint corporate venture of Skidmore, Owings & Merrill; J.E. Greiner Company, Inc.; Parsons, Brinckerhoff, Quade & Douglas; and Wilber Smith & Associates. Baltimore: Interstate Division for Baltimore City.
  59. ^ Nadeau, Gregory G. (August 29, 2014). "HEPH-20" (PDF). Letter to James T. Smith Jr. Washington, DC: Federal Highway Administration. Archived (PDF) from the original on May 7, 2020. Retrieved May 6, 2020 – via American Association of State Highway and Transportation Officials.
  60. ^ Maryland Department of Transportation (2019). "Baltimore SW Map No. D-12B" (PDF) (Map). Statewide Grid Map. 1:12,000. Annapolis: Maryland Department of Transportation. Archived (PDF) from the original on May 7, 2020. Retrieved May 7, 2020.
  61. ^ Highway Information Services Division (December 31, 2020). Highway Location Reference. Maryland State Highway Administration. Retrieved November 5, 2023.
  62. ^ Lenhart, Jennifer (August 28, 2006). "In Biotech Hubs, Labs Play A Vital Role in the Culture". The Washington Post. Retrieved May 13, 2009.
  63. ^ Vick, Karl (February 3, 1997). "Md. Tollway Remains a Road Not Taken". The Washington Post. p. A01. Retrieved January 26, 2011.
  64. ^ Dresser, Michael (February 7, 2011). "First phase of ICC to open Feb. 22". Baltimore Sun. Retrieved February 7, 2011.
  65. ^ Liu, Mimi (February 23, 2011). "More than 10,000 vehicles travel on first stretch of the ICC Wednesday morning". The Gazette. Retrieved February 23, 2011.

External links

Wikimedia Commons has media related to Interstate 70 in Maryland.


Interstate 70
Previous state:
Pennsylvania 		Maryland Next state:
Terminus
Retrieved from "https://wiki.aaroads.com/w/index.php?title=Interstate_70_in_Maryland&oldid=259625#Woodlawn_to_Baltimore"