Grade separation

From the AARoads Wiki: Read about the road before you go
(Redirected from Grade-separated)
Jump to navigation Jump to search
An example of the potential complexity of grade separation, seen in the Jane Byrne Interchange in Chicago
Seven various overpasses for grade separation in Spain near Barcelona
Rail-rail grade separation in Xiaoshan, China
The concept of grade separation includes all transport modes, such as a simple pedestrian bridge over rail tracks.

In civil engineering (more specifically highway engineering), grade separation is a method of aligning a junction of two or more surface transport axes at different heights (grades) so that they will not disrupt the traffic flow on other transit routes when they cross each other. The composition of such transport axes does not have to be uniform; it can consist of a mixture of roads, footpaths, railways, canals, or airport runways. Bridges (or overpasses, also called flyovers), tunnels (or underpasses), or a combination of both can be built at a junction to achieve the needed grade separation.

In North America, a grade-separated junction may be referred to as a grade separation[1][2] or as an interchange – in contrast with an intersection, at-grade, a diamond crossing or a level crossing, which are not grade-separated.

Effects

Advantages

Roads with grade separation generally allow traffic to move freely, with fewer interruptions, and at higher overall speeds; this is why speed limits are typically higher for grade-separated roads. In addition, reducing the complexity of traffic movements reduces the risk of accidents.

Disadvantages

Grade-separated road junctions are typically space-intensive, complicated, and costly, due to the need for large physical structures such as tunnels, ramps, and bridges. Their height can be obtrusive, and this, combined with the large traffic volumes that grade-separated roads attract, tend to make them unpopular to nearby landowners and residents. For these reasons, proposals for new grade-separated roads can receive significant public opposition.

Rail-over-rail grade separations take up less space than road grade separations: because shoulders are not needed, there are generally fewer branches and side road connections to accommodate (because a partial grade separation will accomplish more improvement than for a road), and because at-grade railway connections often take up significant space on their own. However, they require significant engineering effort, and are very expensive and time-consuming to construct.

Grade-separated pedestrian and cycling routes often require modest space since they do not typically intersect with the facility (such as a highway) that they cross. However, grade-separated pedestrian crossings with steps introduce accessibility problems. Some crossings have lifts, but these can be time-consuming to use.

Grade-separated roads that permit for higher speed limits can actually reduce safety due to 'weaving' (see below) as well as a perceived sense of safety.

Roads

Overview

The term is most widely applied to describe a road junction in which the direct flow of traffic on one or more of the roads is not disrupted. Instead of a direct connection, traffic must use on and off ramps (United States, Australia, New Zealand) or slip roads (United Kingdom, Ireland) to access the other roads at the junction. The road which carries on through the junction can also be referred to as grade separated.

Typically, large freeways, highways, motorways, or dual carriageways are chosen to be grade separated, through their entire length or for part of it. Grade separation drastically increases the capacity of a road compared to an identical road with at-grade junctions. For instance, it is extremely uncommon to find an at-grade junction on a British motorway; it is all but impossible on a U.S. Interstate Highway, though a few do exist.

If traffic can traverse the junction from any direction without being forced to come to a halt, then the junction is described as fully grade separated or free-flowing.

A plane on a taxiway over the Autobahn at Leipzig-Halle Airport - a type of grade separation.

Types

Fully separated

These junctions connect two freeways:

4 level stack interchange between the M25 (below) and M23 (above) in the UK.

Partially separated

These junctions connect two roads, but only one is fully grade-separated, i.e. traffic on one road does not have to stop at yield lines or signals on one road, but may have to do so when switching to the other:

Weaving

An example of weaving, where traffic drives on the left. The blue car entering the grade separated road and the red car exiting must both change lanes in the short distance provided.

On roadways with grade-separated interchanges, weaving is a result of placing an exit ramp a short distance after an entry ramp, causing conflicts between traffic attempting to leave the roadway at the next junction and traffic attempting to enter from the previous junction. This situation is most prevalent either where the junction designer has placed the on-slip to the road before the off-slip at a junction (for example, the cloverleaf interchange), or in urban areas with many close-spaced junctions. The ring road of Coventry, England, is a notorious example, as are parts of the southern M25, the London orbital motorway, the M6/M5 junction north-west of Birmingham, and the A4/M5 junction west of Bristol. Weaving can often cause side-on collisions on very fast roads with top speeds of up to 200 kilometres per hour, as well as the problem of blind spots.

Where junctions have unusual designs weaving can be a problem other than on the main road. An example of this can be found at Junction 7 of the M6, where traffic joining the roundabout from the M6 Eastbound off-slip must weave with the traffic already on the roundabout wishing to use the M6 Westbound on-slip. This is as a result of the slip roads on the west side of the junction connecting to the roundabout on the inside of the eastern arc rather than the outside of the western arc as is normal. The two slip-roads are connected by a single lane on the inside of the roundabout, which traffic wishing to use the Westbound on-slip must join, and traffic from the Eastbound off-slip must leave.

Weaving can be alleviated by using collector/distributor roads or braided ramps[3] to separate entering and exiting traffic.

Footbridges and subways

Footbridges and pedestrian/cyclist subways (called underpasses in North America as well as in the United Kingdom when referring to roads) are often employed to allow pedestrians and cyclists to cross busy streets and highways. Though introduced to Central Park in New York City in the 1860s, subways are far more common today in Europe, especially in countries such as the Netherlands, and Denmark where cycling is strongly encouraged. Long underpasses may be called tunnels.

References

  1. ^ City of Eureka Municipal Code 71.85 Archived 2012-02-12 at the Wayback Machine (California, USA)
  2. ^ Henry K. Evans (1950). "Read the ebook Traffic engineering handbook by Institute of Traffic Engineers". ENGINEERING HANDBOOK, Second Edition 1950. New Haven, Connecticut: Institute of Traffic Engineers. Retrieved 2010-10-09. Archived 2018-10-13 at the Wayback Machine
  3. ^ Texas Department of Transportation. "Braided Ramp". TxDOT Visual Dictionary. Archived 2020-03-06 at the Wayback Machine